DC326 is the uncoated series in the catalogue. 542 part numbers, diameters from 0.04 mm to 3.175 mm, standard record ground to -0.003 mm.
It exists because a coating is not always an improvement. At small diameters a coating can cost more than it gives.
The numbers behind the series
- Diameter range: 0.04 mm to 3.175 mm.
- Part numbers: 542.
- Tolerance on the standard record: -0.003 mm.
- Substrate: tungsten carbide, 89-93 HRA.
- Point geometry: 118°, web thinned.
- Coating: none.
The upper limit of 3.175 mm is not arbitrary. It is 1/8 inch, and above that diameter a coated tool usually wins on tool life. Below it the arithmetic changes.
Why uncoated wins at small diameters
A PVD coating is 2-4 µm thick. On a 3 mm drill that is 0.1% of the diameter, and the edge stays sharp enough. On a 0.1 mm drill it is 3% of the diameter, applied to both flanks, so the edge radius grows with it.
A blunt edge does not cut. It pushes. Thrust rises, the drill wanders on entry, and the hole comes out oversized.
Three other effects matter:
- Edge radius. Uncoated carbide can be ground and honed to a smaller radius than a coated tool allows.
- Coating defects. Droplets and pinholes from the PVD process are starting points for adhesion wear in soft materials.
- Regrinding. An uncoated tool can be re-sharpened and returned to service without stripping and recoating.
Where uncoated is the wrong answer
Do not treat DC326 as a universal substitute for a coated series.
- Steel at production speed. Without a coating there is no thermal barrier between chip and edge, and life falls sharply above about 30 m/min in carbon steel.
- Gummy stainless. No low-friction layer means built-up edge, and built-up edge means a poor hole.
- Long unattended runs. A coated tool at the same parameters usually lasts longer, which is what matters when nobody is watching.
For those jobs look at DC426, black-coated and covering 0.04-3.0 mm, or DC836 for bronze coating up to 14 mm.
Reading the -0.003 mm tolerance
The standard record is ground to a negative tolerance: the actual diameter sits at most 0.003 mm below nominal, never above. A nominal 0.500 mm tool measures between 0.497 mm and 0.500 mm.
That is a property of the tool, not of the hole. A drilled hole still comes out larger than the drill because of runout, wander and elastic recovery of the work material. The tolerance guarantees you will not start oversized. The arithmetic is set out in what a minus 0.003 mm tolerance means.
The family around DC326
| Series | Diameter range | Part numbers | Note |
|---|---|---|---|
| DC326 | 0.04-3.175 mm | 542 | Uncoated, -0.003 mm |
| DC326L | 0.04-3.01 mm | 517 | Extended length |
| HDC326 | 0.03-4.1 mm | 507 | Not for shrink-fit holders |
| DC826 | 0.13-10.3 mm | 399 | Uncoated, larger diameters |
HDC326 deserves a note. The "not for shrink-fit holders" restriction is not marketing. A shrink-fit holder clamps by thermal contraction and grips harder than a collet. On a very small shank that is enough to affect runout, and the geometry was ground for a collet.
DC326 or DC326L
Take the extended version when depth exceeds about 5 x D and the machine can still hold runout. A longer drill is a less stiff drill. Below 5 x D the extra length buys nothing and costs stiffness.
FAQ
Is DC326 suitable for aluminium?
Yes, and it is often the preferred choice: polished uncoated flutes with no coating for aluminium to adhere to. See the aluminium selection guide.
Can DC326 be used in mild steel?
Yes, at reduced speed and feed, for short runs. Expect a fraction of the life a coated tool would give.
What does 89-93 HRA mean?
Rockwell A hardness of the carbide substrate, not of the coating. It corresponds to the K10-K20 range used for drills and reamers.
Why is 3.175 mm the top of the range?
3.175 mm is 1/8 inch. Above that diameter the shank is no longer the limiting factor and coated series take over.