The point angle is the included angle at the tip. It decides how much of the drill touches the work at once, and therefore how much thrust the machine has to supply.
118° is the oldest standard in drilling and still the most common. It is a compromise, and it is worth knowing which side of it you are on.
What the angle changes
Three things move together when the point gets sharper or blunter.
Chisel edge length. At 118° the chisel edge is long relative to the diameter. A 135° point shortens it. The chisel edge does not cut; it extrudes material. A long chisel edge means high thrust and a tendency to wander on a curved or inclined surface.
Thrust. Because of the chisel edge, a 118° drill needs noticeably more axial force than a 135° drill at the same diameter and feed. On a 0.3 mm drill that is the difference between a stable hole and a snapped tool.
Centring. A blunter point self-centres. A sharper point skates. This is why 118° drills are usually spotted before entering a curved surface.
When 118° is the right choice
- Aluminium, brass, copper. Soft material cuts easily and the long chisel edge costs little.
- Plastics and composites. Lower edge pressure means less delamination at breakthrough.
- Thin sheet. A 118° point breaks through more gently than 135°, with less deformation around the exit.
- General purpose work on low-rigidity machines. The geometry is forgiving.
- Small batches where one tool must cover several jobs.
When it is the wrong choice
- Austenitic stainless and alloy steel. Thrust is high and the material work-hardens under it. Use 135°.
- Hardened or pre-hardened stock. The point will not penetrate without excessive force.
- Deep holes. A long chisel edge plus a long flute is a recipe for wander.
- Entry on a curved or inclined surface without a spot drill.
Web thinning matters more than the angle
A 118° point with a heavy web behaves worse than a thinned 118° point by a wide margin. Thinning removes material behind the chisel edge and shortens the non-cutting zone. Every micro series in this catalogue is web thinned, and the quoted point angle assumes it.
If a drill wanders on entry, check thinning and runout before you question the angle.
118° and 135° side by side
| 118° | 135° | |
|---|---|---|
| Chisel edge | Long | Short |
| Thrust at the same feed | Higher | Lower |
| Self-centring | Poor | Good |
| Thin sheet | Better | More aggressive |
| Stainless, alloy steel | Not advised | Standard |
| Regrinding | Simple | Needs a fixture |
Spotting, and the angle that goes with it
A 118° drill entering an inclined surface should be spotted first. The spot drill does two jobs: it creates a flat land for the point to start on, and it fixes the position.
Use a spot drill with a slightly larger point angle than the drill, so the drill seats on the flank of the cone rather than at the bottom. A 90° spot drill is common and works; a 120° spot leaves a cone that a 118° drill sits into cleanly.
A spot depth of 0.5-1 x D is enough. A deep spot wastes time and can leave a burr that deflects the drill.
Position error, not just thrust
The point angle also decides where the hole ends up. A drill that skates on entry keeps the error: 0.02 mm of wander at the surface becomes 0.02 mm of position error at the bottom.
On a 0.3 mm drill, 0.02 mm is 7% of the diameter. That is why the position tolerance on a micro hole is usually set at the entry, not by the drilling itself.
Interaction with coating
There is none worth planning around. A coating changes friction and hot hardness; it does not change the load distribution that the point angle sets. Choose the angle from the material and the machine, then choose the coating from the edge temperature.
FAQ
Can I regrind a 118° drill to 135°?
Above about 3 mm, yes, with a proper fixture. Below 1 mm the web and margin are too small to rework reliably. Buy the geometry you need.
Why does my drill wander on entry?
Usually runout above 0.005 mm, or a long chisel edge entering an inclined surface. Spot first, or move to a 135° point.
Is 118° suitable for stainless steel?
It will drill, but expect higher thrust, faster work hardening and shorter life. The stainless series in the catalogue use 135°.
Does the point angle change the hole size?
Only indirectly. A sharper point wanders more on entry, and wander shows up as position error and oversize.