ISO 9001 CERTIFIED MANUFACTURER IN-HOUSE GRINDING · COATING · INSPECTION

Coating notes: TiN coating on carbide tools

TiN is the general-purpose PVD layer: 2400-2500 HV, good to about 600 °C. Where it pays, and why it fails on aluminium.

5 min read 905 words Updated 2026-11-19

TiN, titanium nitride, is the coating every catalogue has and every machinist has used. It is a good general-purpose PVD layer, and it is the wrong choice in a few specific situations.

What the layer is

TiN is deposited by PVD in a layer 2-4 µm thick. It is gold coloured, has a hardness of 2400-2500 HV and a friction coefficient against steel of roughly 0.4-0.5.

Its service limit is 550-600 °C. Above that the layer oxidises to titanium oxide, which is soft and protects nothing.

What it buys you

  • Lower friction on the rake face. Chips flow and carry heat away with them.
  • A thermal barrier. The carbide substrate runs cooler than an uncoated tool at the same speed.
  • Less crater wear in carbon and alloy steel.
  • A visible wear indicator. A worn TiN tool shows the substrate through the coating, which is useful when setting tool-change intervals.

In carbon steel the practical effect is 20-50% more tool life at the same parameters, or the same life at a higher cutting speed.

Where TiN is wrong

Aluminium

Aluminium adheres to TiN. Once a lump of work material welds to the edge, the coating stops mattering and the hole starts going oversized. Uncoated polished flutes or DLC are the correct answer; see the aluminium guide.

Very small diameters

A 3 µm coating on a 0.1 mm drill is 3% of the diameter, applied to both flanks. The edge radius becomes a significant fraction of the chip thickness, thrust rises and the drill wanders. Below roughly 0.2 mm, uncoated is usually the better tool.

Cast iron and abrasive work

The wear mechanism is abrasion rather than adhesion. A harder layer holds up better.

Anything above 600 °C at the edge

Stainless at high speed, titanium alloys and dry deep-hole drilling exceed the limit. The coating oxidises and the tool fails as if it were uncoated.

TiN in the catalogue

SeriesDiameterPart numbersGeometry
HDC6360.15-3.72 mm997Left-hand, 135°
DC6360.28-6.03 mm233Left-hand, 135°
HDCS6360.43-3.0 mm1508Left-hand step drill

The TiN range here is weighted toward left-hand and step geometry, both production features on automatic lathes rather than general-purpose tools. For general drilling in carbon steel on a right-hand spindle, the black-coated DC426 and bronze-coated DC836 cover the same diameters.

Comparing the coatings in this catalogue

CoatingHardnessService limitFirst choice for
Uncoated1800-2000 HVedge-limitedAluminium, plastics, below 0.2 mm
DLC1800-2200 HV350-400 °CGummy aluminium, dry or MQL
TiN2400-2500 HV550-600 °CCarbon and alloy steel, general work
Black2000-2400 HV500-600 °CGeneral steel, cost-sensitive runs
Bronze2200-2500 HV500-550 °CStainless, abrasive grades

The table is a starting point, not a rule. Two tools with the same coating can behave differently because of edge preparation, so treat the coating as one variable among three: geometry, coating, parameters.

Thickness, and why it is quoted in micrometres

A PVD layer is specified at 2-4 µm because that is the range where it protects without blunting. Thicker is not better: at 6 µm the layer carries more residual stress, spalls at the edge, and on a small drill it changes the cutting geometry.

Thickness is measured on a polished cross-section or by X-ray fluorescence on a reference coupon, not on the tool in your hand. What you can check in the shop is colour and edge condition under a microscope.

Cost per hole, not cost per tool

A TiN drill costs more than an uncoated drill. Whether it is cheaper depends on how many holes it makes.

Take a 1.0 mm drill in carbon steel at 25 m/min. Uncoated life might be 400 holes; TiN at the same parameters might reach 600. If a tool change costs five minutes of spindle time, the coated tool wins even at twice the price.

The calculation reverses in aluminium, where TiN brings no life gain and only adds adhesion risk.

Practical rules

  1. Choose TiN when the work is carbon or alloy steel, the speed is moderate and the tool is above 0.3 mm.
  2. Do not choose it for aluminium, for cast iron, or for holes where the edge will exceed 600 °C.
  3. A coated drill is not a sharper drill. If the edge geometry is wrong for the material, the coating will not rescue it.
  4. Recoating a reground tool is possible but rarely economical below 1 mm.

FAQ

Does TiN change the hole size?

Not directly. It adds up to 6 µm to the diameter, which the manufacturer accounts for in the coated record. A hole-size change you observe is more likely runout or built-up edge.

TiN or TiAlN?

TiAlN-type coatings keep their hardness to higher temperatures and suit stainless and dry cutting better. TiN remains cheaper and adequate for general steel.

Why does my TiN drill look copper-coloured after a few holes?

Heat tint. The layer is oxidising. If it happens early, cutting speed is too high or coolant is not reaching the edge.

Data behind the text

Dimensions and part numbers referenced here come from the TONNY production catalogue. Open the series or diameter index to check a specific record before ordering.

Browse series   Diameter index