ISO 9001 CERTIFIED MANUFACTURER IN-HOUSE GRINDING · COATING · INSPECTION

Failure analysis: Why a micro drill breaks

A micro drill breaks when thrust or bending exceeds its section. Read the fracture face, fix runout first, then peck depth and feed.

4 min read 707 words Updated 2026-11-19

A micro drill does not wear out quietly. It snaps. The reason is arithmetic: strength scales with the square of diameter, and cutting force does not.

A 0.3 mm drill has a cross-section of 0.07 mm². A modest 50 N of thrust puts 700 MPa into it before any bending is added. Once bending starts, the tool lives on the difference between carbide strength and the stress a small misalignment creates.

Read the fracture before changing anything

The break face tells you which load killed the tool.

AppearanceLoadUsual cause
45° shear lip, flutes twistedTorsionChip packing, feed too high, hole bottom
Transverse break, flutes intactBendingRunout, wander, holder, overhang
Corner chipping, no twistImpactInterrupted entry, cross-hole, scale
Wear land, then crumblingHeat and abrasionSpeed too high, coolant starved
Crack from the margin, slow growthFatigueVibration, unstable holder

A torsional break means torque exceeded the section. A bending break means the tool was pushed sideways. They have different fixes, and guessing wastes tools.

Cause one: runout

Below 1 mm, total indicated runout should stay under 0.005 mm. Above that the drill rotates off-centre, one flute does most of the cutting, and the side force bends a tool with almost no bending stiffness.

Check in this order: collet condition, collet nut torque, spindle taper, shank cleanliness. A 10 µm chip on the shank is 3% of a 0.3 mm diameter, and that is enough.

Cause two: feed that is too low

This one is counter-intuitive. Operators reduce feed when a drill breaks, and a drill that rubs is more likely to break than a drill that cuts.

Below a threshold feed the edge cannot penetrate; it burnishes. Thrust rises, the material work-hardens, and the next revolution is harder still. The drill breaks and the operator reduces the feed again.

For micro diameters, keep feed per revolution between 0.5% and 2% of diameter. At 0.3 mm that is 0.0015-0.006 mm/rev.

Cause three: chip evacuation

A 0.5 mm hole at 10 x D holds about 0.002 cm³ of material. That does not sound like much, but the chips must leave through two flutes with almost no clearance.

  • Peck at 1 x D in steel and stainless, 2-3 x D in aluminium.
  • Use through-coolant above 5 x D when the series supports it.
  • Retract at rapid, return at rapid, and keep cutting feed inside the hole.
  • Watch for chips dragged back into the flutes on the return.

Cause four: entry

A drill entering a curved, inclined or interrupted surface is in single-point contact. The side force is large and the tool is at its least supported.

Spot with a 90° or 118° spot drill, or use a flat-bottom drill for the first 1 x D. On cross-holes, reduce feed to about 30% through the intersection.

Cause five: overhang

Stiffness falls with the cube of overhang. Doubling the stick-out makes the tool eight times more flexible. Use the shortest drill that reaches the depth, and prefer an extended-length series over pulling a standard drill out of the collet.

A short diagnostic sequence

  1. Measure runout at the tool tip. Above 0.005 mm, stop and fix it.
  2. Match the fracture face to the table above.
  3. Torsional break: halve the peck depth, verify feed per revolution.
  4. Bending break: fix runout before touching parameters.
  5. Discoloration: reduce speed by 20% and check coolant delivery.

FAQ

Can a harder coating stop breakage?

No. Breakage is a mechanical overload. A coating changes friction and hot hardness; it does not change the section modulus.

Why does the drill break at the same depth every time?

Chip packing. The flutes fill at a predictable depth, torque spikes and the tool twists off. Shorten the peck.

Is a left-hand drill stronger?

No. Left-hand geometry exists for machines that run in reverse and for pull-drilling.

Do I need a torque-adaptive control?

For production at 0.2 mm and below it helps, but runout and peck depth fix more breakages for less money.

Data behind the text

Dimensions and part numbers referenced here come from the TONNY production catalogue. Open the series or diameter index to check a specific record before ordering.

Browse series   Diameter index